Amana washing machines are widely used in the United States and Canada, including traditional top-load, high-efficiency top-load and front-load models. Modern Amana washers use electronic controls and multiple sensors to monitor water filling, draining, motor operation, load balance, door or lid locking, water level and other operating conditions.

When the washer detects an abnormal condition, it may stop or modify the cycle and display an error or status code.

Common codes include:

• F1 E1
• F3 E1
• F5 E2
• F5 E3
• F7 E1
• F8 E1
• F8 E3
• F9 E1
• LF
• LD / Ld
• Sd / Sud
• UL
• OL
• HC
• LOC / LoC / LC

Amana's current support information confirms that error-code families differ between front-load and top-load machines. For example, Amana lists F-code families separately for front-load and top-load washers.

Therefore, the exact meaning of a code must always be verified against the model number and its technical documentation before replacing components.

Quick Amana Washer Error Code Reference

Error Code	Typical Meaning / Area to Check
F1 E1	Main electronic/control-system fault on applicable models
F3 E1	Water-level/pressure sensing fault on applicable models
F5 E2	Door/lid locking problem
F5 E3	Door/lid unlocking problem on applicable models
F7 E1	Motor speed sensing / drive-related problem
F8 E1	Low or insufficient incoming water flow
F8 E3	Water-level/overflow-related fault on applicable platforms
F9 E1	Long drain / washer taking too long to drain
LF	Long Fill
LD / Ld	Long Drain
Sd / Sud	Excessive detergent suds
UL / uL	Unbalanced load on applicable models
OL / oL	Overloaded washer on applicable models
HC	Hot and cold inlet hoses reversed
LOC / LoC / LC	Control Lock enabled

Important: Some older and newer Amana platforms use different codes or definitions. Treat this table as a diagnostic starting point rather than a substitute for model-specific service literature.

1. Amana Washer F1 E1 Error Code

What does F1 E1 mean?

On applicable Amana washer platforms, F1 E1 generally points toward an electronic control or main control-system fault.

Possible causes can include:

• Temporary control-board malfunction
• Power interruption
• Incorrect or unstable supply voltage
• Loose wiring connection
• Damaged wiring harness
• Main control board failure

How to troubleshoot F1 E1

First perform a complete power reset.

1. Stop the washer.
2. Disconnect it from electrical power.
3. Leave it disconnected for approximately five minutes.
4. Restore power.
5. Select a normal cycle.
6. Check whether the fault returns.

Amana recommends a five-minute power cycle as a general reset procedure for washer control problems.

If F1 E1 immediately returns, further electrical diagnosis may be necessary.

A technician may need to inspect the control board, connectors, wiring harness and incoming power before determining that the electronic control requires replacement.

2. Amana Washer F3 E1 Error Code

What does F3 E1 mean?

On applicable platforms, F3 E1 is associated with the washer's water-level or pressure-sensing system.

The washer uses water-level information to determine how much water is inside the tub.

Possible causes include:

• Pressure-sensor problem
• Pressure hose blocked or damaged
• Loose pressure hose
• Wiring problem
• Electronic control problem
• Abnormal water-level reading

Troubleshooting

Disconnect power before opening the appliance.

Check:

• Pressure hose for kinks
• Hose for cracks
• Air trap for blockage
• Electrical connectors
• Sensor wiring
• Signs of water or corrosion near connectors

Do not automatically replace the pressure sensor solely because F3 E1 appears. Confirm the model-specific diagnostic procedure first.

3. Amana Washer F5 E2 Error Code

Meaning

For supported Amana front-load washers, F5 E2 indicates that the door is not locking properly.

Without confirmation that the door is securely locked, the washer cannot safely enter high-speed operation.

Possible causes

• Clothing trapped in the door
• Door not completely closed
• Detergent residue around the latch
• Door strike misaligned
• Door-lock assembly failure
• Loose wiring
• Control-system problem

Solution

Open the door and inspect the complete sealing area.

Remove clothing or foreign objects that could prevent closure.

Close the door firmly and retry the cycle.

Amana's published guidance for applicable front-load machines recommends checking for objects blocking the door and making sure it closes completely.

If the error repeatedly returns, the lock assembly and associated wiring may require diagnosis.

4. Amana Washer F5 E3 Error Code

F5 E3 belongs to the door/lid-lock error family on applicable Amana platforms and commonly requires investigation of the unlocking/lock mechanism.

Possible causes include:

• Door-lock mechanism problem
• Mechanical obstruction
• Damaged latch
• Wiring problem
• Electronic control problem

Never force a locked washer door.

If water remains inside the washer, solve the drainage problem before attempting further door-lock diagnosis.

5. Amana Washer F7 E1 Error Code

Meaning

Amana identifies F7 E1 on applicable front-load washers as a motor speed sensing error. The motor is unable to achieve the correct speed required for the selected cycle.

Possible causes

• Washer overloaded
• Shipping bolts still installed on a newly installed machine
• Motor problem
• Speed-sensing problem
• Wiring harness issue
• Drive-system obstruction
• Electronic control issue

Solution

Remove some clothing if the washer is overloaded.

For a newly installed front-load washer, confirm that all transportation/shipping bolts have been removed.

Try running the machine with a smaller load.

If the error continues, professional diagnosis of the motor, speed feedback circuit and control electronics may be necessary.

6. Amana Washer F8 E1 Error Code

Meaning

F8 E1 means the washer is not detecting the expected amount of incoming water. Amana also associates this condition with Lo FL or a "No Water Detected" message on applicable models.

Top-load Amana documentation similarly groups LF, Lo FL and F8 E1 with a washer taking too long to fill.

Common causes

• Water faucet closed
• Low household water pressure
• Kinked inlet hose
• Clogged inlet screen
• Frozen water pipe
• Faulty inlet valve
• Incorrect drain-hose installation
• Water being siphoned from the tub

Troubleshooting

Check both hot and cold water valves.

They should normally be fully open.

Inspect the inlet hoses for:

• Kinks
• Crushing
• Blockages
• Restricted flow

Amana specifically recommends confirming that the household water supply is on, hot and cold valves are fully open and inlet hoses are not kinked.

7. Amana Washer F8 E3 Error Code

On washer platforms that use it, F8 E3 belongs to the water-level/fill-system fault family and may indicate an abnormal water-level or overflow-related condition.

Possible areas requiring diagnosis include:

• Water inlet valve
• Pressure/water-level sensor
• Pressure hose
• Wiring
• Electronic control

If the washer continues filling when it should stop, immediately turn off the household water supply and disconnect power.

A mechanically stuck inlet valve can sometimes allow water to enter even when the washer is not actively requesting it.

Because F8 E3 definitions can be platform-specific, verify the model's service documentation before replacing components.

8. Amana Washer F9 E1 Error Code

Meaning

For supported front-load Amana washers, F9 E1 indicates that draining is taking longer than expected. Amana notes that this typically means a drain time exceeding approximately eight minutes.

Possible causes

• Kinked drain hose
• Blocked drain hose
• Drain pump obstruction
• Excessive detergent suds
• Incorrect standpipe installation
• Drain pump failure

Solution

Check the drain hose carefully.

Make sure it is:

• Not kinked
• Not crushed
• Not clogged
• Installed at the proper height
• Secured correctly

Amana specifies a standpipe height range of approximately 39 inches minimum to 96 inches maximum for the front-load guidance associated with this code.

Also investigate excessive detergent use because oversudsing can slow drainage.

9. Amana Washer LF Error Code

Meaning

LF means Long Fill.

The washer is taking longer than expected to obtain the required amount of water.

Amana groups LF, Lo FL and F8 E1 together on applicable top-load HE machines as fill-related problems.

Check

• Hot water faucet
• Cold water faucet
• Water pressure
• Inlet hoses
• Inlet screens
• Water inlet valve
• Drain-hose position

If both water supplies are fully open but LF repeatedly returns, further diagnosis of the inlet valve and water-level sensing system may be necessary.

10. Amana Washer LD / Ld Error Code

Meaning

Ld means Long Drain.

The washer is taking too long to remove water.

Amana describes Ld as a drain pump system problem/long drain condition.

Possible causes

• Blocked drain hose
• Incorrect drain-hose installation
• Drain pump obstruction
• Foreign object in drain system
• Pump failure
• Excessive suds

Amana also warns that inserting the drain hose too far into the standpipe can contribute to drainage problems; its Ld guidance specifically calls attention to correct drain-hose installation.

11. Amana Washer Sd / Sud Error Code

Meaning

Sd or Sud indicates excessive suds inside the washer.

This is frequently a detergent-use problem rather than an electronic failure.

Amana states that the washer may automatically extend rinsing and pause operation while attempting to reduce excessive foam.

Common causes

Too much detergent

Using excessive detergent is one of the most common causes.

Non-HE detergent

High-efficiency washers should use HE detergent.

Incorrect detergent concentration

Modern detergents may be concentrated at different levels such as 2x, 4x or 8x.

Follow the detergent manufacturer's recommended quantity for the load size and soil level.

Restricted drainage

A partially blocked drain can also contribute to an Sd/Sud condition.

Amana notes that a restricted drain hose or standpipe can be associated with this code.

What should you do?

Allow the washer's automatic suds-reduction routine to finish.

Reduce detergent on future loads.

If necessary, run an additional rinse/spin cycle.

Amana warns that excessive suds can result in reduced spin speed, wet clothing, additional rinses and longer cycle times.

12. Amana Washer UL / uL Error Code

On applicable washer platforms, UL/uL indicates an unbalanced load.

The washer has detected that clothing is not distributed evenly enough for safe high-speed spinning.

Common causes

• One heavy item
• Blankets
• Towels concentrated on one side
• Very small load
• Overloaded washer
• Washer not level
• Weak suspension components

Solution

Pause the washer.

Redistribute the clothing evenly around the basket.

If necessary, remove several items.

Make sure the washer stands firmly and level on the floor.

Repeated imbalance with normal loads may justify inspection of the suspension system.

13. Amana Washer OL / oL Error Code

On applicable models, OL/oL generally indicates an overloaded washer condition.

Too much laundry can prevent the basket or drive system from operating correctly.

Solution

Remove several items from the washer.

Do not compress clothing tightly into the basket.

Retry the cycle with a smaller load.

Persistent overload indications with a normal load may require diagnosis of the drive, basket movement or load-sensing system.

14. Amana Washer HC Error Code

Meaning

HC commonly indicates that the hot and cold water inlet hoses are reversed.

Amana's top-load HE guidance states that this code can appear at the end of a wash cycle when the cold hose is connected to the hot inlet and the hot hose is connected to the cold inlet.

Solution

Turn off both water faucets.

Check the washer's inlet markings:

H = Hot

C = Cold

Reconnect the hoses correctly.

Turn the water supply back on and test another cycle.

15. Amana Washer LOC / LoC / LC Code

Meaning

LOC, LoC or LC is usually not a hardware failure.

It indicates that Control Lock has been activated.

Amana confirms that applicable front-load models may display LoC or LC when buttons are pressed while Control Lock is enabled.

Solution

Locate the Control Lock button or the control-panel button marked with a lock symbol.

Press and hold the appropriate button according to the instructions for your exact model.

Because the button combination and hold duration can vary, consult the model's user manual if the lock does not deactivate.

How to Reset an Amana Washer

A reset can sometimes clear temporary electronic errors.

General reset procedure

1. Turn the washer off.
2. Unplug it from the electrical outlet.
3. If hard-wired, switch off its circuit breaker.
4. Wait approximately five minutes.
5. Restore electrical power.
6. Select the desired cycle.
7. Start the washer again.

This five-minute power-cycle procedure is consistent with Amana's published washer reset guidance.

However, resetting the washer does not repair a mechanical, electrical or plumbing fault. If the code repeatedly returns, diagnose the underlying cause.

Troubleshooting an Amana Washer That Will Not Fill

For F8 E1, LF or similar fill problems, check the system in this order:

Water supply → faucets → hoses → inlet screens → inlet valve → water-level sensing → wiring/control

Both hot and cold water supplies should normally be available.

A restricted hose can substantially increase fill time even if some water still enters the washer.

Troubleshooting an Amana Washer That Will Not Drain

For LD, F9 E1 or related drain problems, check:

Tub → pump inlet → drain pump → drain hose → standpipe → household drain

Common foreign objects include:

• Coins
• Buttons
• Hair
• Lint
• Small socks
• Fabric
• Other debris

Disconnect electrical power before accessing internal components.

Troubleshooting an Amana Washer That Will Not Spin

If an Amana washer fills and drains but does not spin correctly, investigate:

• Load balance
• Overloading
• Door/lid lock
• Excessive suds
• Drainage
• Motor
• Motor speed sensing
• Drive components
• Wiring
• Electronic control

Remember that a washer may intentionally prevent high-speed spinning if it cannot confirm that the door/lid is locked or that water has drained sufficiently.

When Should You Call a Technician?

Professional diagnosis is recommended when:

• An F-code immediately returns after reset
• Water continues entering uncontrollably
• Washer trips the circuit breaker
• Burning smell is present
• Electrical components show heat damage
• Drain pump receives power but does not operate
• Motor will not run
• Door remains permanently locked
• Wiring is damaged
• Electronic control failure is suspected
• Internal electrical measurements are required

Electrical testing should only be performed by someone qualified to work safely around mains-powered appliances.

Important Model-Specific Warning

Do not assume that every Amana washer uses identical error-code definitions.

Amana maintains different error-code resources for front-load washers and top-load washers, and its current top-load support index contains numerous additional F-code and status-code families.

Before purchasing replacement parts, obtain the washer's:

• Model number
• Serial number
• Exact displayed error code

Then compare the fault against the owner's manual, technical sheet or official Amana documentation for that specific machine.

Amana Washer Product Help

Frequently Asked Questions (FAQ)

1. How do I clear an error code on an Amana washer?

Correct the underlying problem first. A temporary electronic error may sometimes be cleared by disconnecting the washer from power for approximately five minutes and reconnecting it.

2. What does F8 E1 mean on an Amana washer?

F8 E1 means the washer is not detecting the expected incoming water flow. Check the water supply, faucets and inlet hoses first.

3. Is LF the same as F8 E1?

They can describe closely related long-fill/low-flow conditions on applicable models. Amana groups LF, Lo FL and F8 E1 together in its top-load HE guidance.

4. What does F9 E1 mean?

On applicable front-load machines, F9 E1 means the washer is taking longer than expected to drain.

5. Why does my Amana washer display Sud or Sd?

The washer has detected excessive suds. Too much detergent, non-HE detergent or drainage restrictions can contribute to this condition.

6. Should I stop the washer when Sud appears?

Usually, allow the washer's suds-reduction routine to continue. The machine may pause and perform additional rinses to remove foam.

7. What does LOC mean on an Amana washer?

LOC/LoC/LC normally indicates that Control Lock is active rather than indicating a failed component.

8. What does HC mean?

On applicable models, HC indicates that the hot and cold water inlet connections are reversed.

9. Why does my Amana washer keep showing LD?

The washer is taking too long to drain. Inspect drain-hose installation and look for restrictions in the drainage system.

10. What does F5 E2 mean?

On applicable front-load models, F5 E2 indicates that the washer door is not locking correctly. Check for clothing or objects preventing complete closure.

11. What does F7 E1 mean?

F7 E1 indicates a motor speed sensing problem on applicable front-load washers. Overloading and unremoved shipping bolts are among the items Amana recommends checking.

12. Can too much detergent cause an Amana washer error?

Yes. Excessive detergent can produce Sd/Sud errors and can lead to additional rinses, slower spinning, longer cycles and wet clothing.

13. Why are my clothes still wet after the cycle?

Possible causes include excessive suds, an unbalanced load, drainage problems, overloading or a spin/drive problem. Amana specifically notes that excess suds can reduce spin speed and leave loads wetter.

14. Can I repair an Amana washer myself?

Basic checks such as inspecting hoses, correcting the load, verifying water supplies, reducing detergent and performing a power reset are generally suitable for users. Internal electrical diagnosis should be left to qualified personnel.

15. Where can I find the exact error-code information for my washer?

Use the complete model number to locate the appropriate owner's manual and product literature. Model-specific documentation should take priority over generic error-code lists.

Conclusion

Amana washer error codes are designed to help identify problems in major systems such as water filling, drainage, door locking, motor operation, water-level sensing, load balance and electronic control.

For many problems, start with simple checks: verify the water supply, inspect hoses, redistribute the load, use the correct amount of HE detergent and perform a power reset where appropriate.

Persistent F-codes, repeated drainage or fill failures, electrical faults and motor/control problems should be diagnosed using the technical information for the exact Amana washer model rather than by replacing parts based solely on a generic error-code definition.

#Tags

#Amana #AmanaWasher #AmanaWashingMachine #AmanaWasherError #AmanaErrorCodes #WasherErrorCodes #WashingMachineErrorCodes #AmanaTroubleshooting #WasherTroubleshooting #WashingMachineRepair #AmanaRepair #ApplianceRepair #WasherRepair #F1E1 #F3E1 #F5E2 #F5E3 #F7E1 #F8E1 #F8E3 #F9E1 #LFError #LDError #SudError #SdError #ULError #OLError #HCError #LOCError #LongFill #LongDrain #WasherNotFilling #WasherNotDraining #WasherNotSpinning #WasherDoorLock #ControlLock #ExcessiveSuds #HEWasher #HEDetergent #FrontLoadWasher #TopLoadWasher #AmanaFrontLoad #AmanaTopLoad #WasherMaintenance #WasherDiagnostics #ApplianceTroubleshooting #DIYWasherRepair #WasherFaultCodes #LaundryAppliance #AmanaWasherHelp